Design and calculation of test stand for testing personal fall protection equipment according to EN 364
Article Sidebar
Main Article Content
Abstract
This paper presents the design and calculation of a test stand intended for testing personal fall protection equipment in accordance with the requirements of the international standard EN 364. The objective of the study was to develop a reliable, safe, and structurally adequate test stand capable of performing both static and dynamic tests on components of fall arrest systems, including different types of personal fall protection systems, fall-arresters, anchor lines, safety harnesses, lanyards, energy absorbers, and connecting elements. The paper analyzes the requirements of EN 364 and defines the functional and structural characteristics of the test stand. Particular emphasis was placed on the static strength of the supporting structure, which was designed to withstand the maximum prescribed test forces without permanent deformation or structural failure, ensuring an adequate safety factor under the most unfavorable loading conditions. Furthermore, the dynamic performance of the test stand was analyzed through the evaluation of its natural frequencies, in accordance with standard requirements. The obtained calculation results confirm that the designed test stand fully complies with the requirements of EN 364 and enables accurate, reliable, and safe testing of personal fall protection equipment, thereby contributing to improved occupational safety and compliance with relevant standards
Article Details
This work is licensed under a Creative Commons Attribution 4.0 International License.
References
[1] N. Krishnamurthy, “Safety at height: A holistic view of fall management”, CRC Press, Taylor & Francis Group, Boca Raton, FL (USA), https://doi.org/10.1201/9781032648132, (2024)
[2] H. Hsiao, “Fall prevention and protection: Principles, guidelines, and practices”, CRC Press, Taylor & Francis Group, Boca Raton, FL (USA), https://doi.org/10.1201/9781315373744, (2017)
[3] G. Drennan Gagnet and M. Drennan, “Fall protection and scaffolding safety: An illustrated guide”, Government Institutes, Rockville, MD (USA), (2000)
[4] BS EN 364:1993, “Personal protective equipment against falls from a height - Test methods”, British Standards Institution, (1993)
[5] J. C. Pomares, E. Á. Carrión, A. González, and P. I. Saez, “Optimization on personal fall arrest systems. Experimental dynamic studies on lanyard prototypes”, International Journal of Environmental Research and Public Health, Vol. 17(3), p. 1107, https://doi.org/10.3390/ijerph17031107, (2020)
[6] E. Á. Carrión, B. Ferrer, J. F. Monge, P. I. Saez, J. C. Pomares, and A. González, “Minimum clearance distance in fall arrest systems with energy absorber lanyards”, International Journal of Environmental Research and Public Health, Vol. 18(11), p. 5823, https://doi.org/10.3390/ijerph18115823, (2021)
[7] J. C. Pomares, E. Á. Carrión, R. Irles, A. González, and E. G. Segovia, “Experimental tests on personal safety devices for falls from height”, WIT Transactions on the Built Environment, Vol. 180, pp. 69–81, https://doi.org/10.2495/SUSI180071, (2018)
[8] C. S. Pan, J. R. Powers, J. J. Hartsell, J. R. Harris, B. M. Wimer, R. G. Dong, and J. Z. Wu, “Assessment of fall-arrest systems for scissor lift operators: Computer modeling and manikin drop testing”, Human Factors, Vol. 54(3), pp. 358–372, https://doi.org/10.1177/0018720811425024, (2012)
[9] M. Bižić and D. Petrović, “Methodology of testing guided-type fall arresters with rail-based rigid anchor lines”, Engineering Today, Vol. 4(1), pp. 31–40, https://doi.org/10.5937/engtoday2500005B, (2025)
[10] J. N. Ellis, “Introduction to fall protection”, American Society of Safety Engineers, IL (USA), (2001)
[11] BS EN 10002-2:1992, “Metallic materials - Tensile testing - Part 2: Verification of the force measuring system of the tensile testing machines”, British Standards Institution, https://doi.org/10.3403/00263687, (1992)
[12] BS EN 10002-1:1990, “Metallic materials- Tensile testing - Part 1: Method of test at ambient temperature”, British Standards Institution, (1990)